变压器内部故障在线检测方法仿真及误差分析

为研究变压器内部故障在线检测方法的有效性及抗干扰性,搭建实际变压器的非线性三维有限元模型.对变压器常见几种类型的内部故障进行详细的结构仿真,通过"场-路耦合法"构建各类型故障的ΔV-I1轨迹.同时,通过对正常绕组的测量信号设置一定的误差,构建了考虑测量误差时的误差轨迹.在此基础上,将正常时的标准轨迹、误差轨迹和各种类型的故障轨迹进行对比分析,通过对ΔV-I1轨迹特征差异的定性分析与定量计算,验证该方法在实际应用中的有效性,总结判断各类型故障的规则,同时针对测量误差所造成的干扰提出了建议.     

爆炸冲击波载荷下预制孔铝板的动态响应

为研究爆炸冲击波对破片穿孔后板结构的毁伤效应,使用激波管为冲击波加载设备,对不同孔形的预制孔铝板进行冲击波加载.利用三维数字图像相关(3 D-DIC)技术,分析固支预制孔方形铝板在冲击波加载条件下的动态响应,得到预制孔铝板的动态响应和变形失效过程.结合3 D-DIC结果分析孔形对靶板刚度、破坏形式、承载能力的影响.结果表明:圆形孔靶板刚度最大,圆形孔靶板的极限承载能力最大,菱形孔靶板极限承载能力最差;孔形对撕裂破坏的影响主要体现在孔的角点在靶板分布上.该实验结果对固支板结构的抗爆设计具有一定参考价值.     

Joint impact of CEE and IQI on NOMA with full-duplex relaying system

Wireless Networks - This paper considers the performance of non-orthogonal multiple-access (NOMA) with full-duplex (FD) relaying system in the presence of two practical undesirable defects, namely...     

稀土灼烧过程温湿度场仿真分析

影响稀土灼烧工艺的因素十分复杂,关系产品质量稳定及能耗,现行工艺存在优化空间。通过剖析灼烧窑中温度和湿度分布状况,运用κ-ε双方程湍流模型、流体传热、多孔介质传热等理论,按特定组分运输模式,建立灼烧过程质量、动量和能量耦合传递数学模型。设置不同边界导入Fluent环境对数学模型进行仿真试验,完成数据处理实现工艺参数优化。结果表明所建模型能准确反映灼烧窑中温湿度场分布及变化,且最终仿真结果与实际灼烧后的产品湿度含量相符合。     

Corrosion behaviour of Mg-Gd-Y-Zn-Ag alloy components with different sizes after cooling

The corrosion behaviour of Mg-6Gd-3Y-1Zn-0.3Ag (wt.%) alloy components with different sizes after cooling was investigated. The alloys in the small components (SC) cooled fast, which were composed of α-Mg matrix and coarse long-period stacking ordered (LPSO) phases. The alloys in the large components (LC) cooled slowly, and there were thin lamellar LPSO phases precipitating inside the grains, except for α-Mg matrix and coarse LPSO phases. The hydrogen evolution test revealed that the corrosion rate of LC sample was higher than that of SC sample. Electrochemical impedance spectroscopy (EIS) test showed that the surface film on LC alloys provided worse protection. The corrosion morphologies indicated that the precipitation of the thin lamellar LPSO phases in LC sample caused severe micro-galvanic corrosion, which accelerated the rupture of the surface film.     

Far-red-emitting YAl3(BO3)4:Cr3+ phosphors with excellent thermal stability and high luminescent yield for plant growth LEDs

Phosphors-converted LEDs (pc-LEDs) are excellent artificial light sources for indoor plant cultivation, in which the far-red-emitting component (700−780 nm) plays an important role in regulating the photomorphogenesis of plants. Accordingly, highly efficient and thermally stable far-red-emitting phosphors are indispensable for developing high-performance plant cultivation pc-LEDs. Herein, far-red-emitting YAl₃(BO₃)₄:Cr³⁺ (YAB:Cr³⁺) phosphors were synthesized by solid-state reaction, and their photoluminescence characteristics, thermal quenching, quantum yield (QY), and application in pc-LEDs were systematically investigated. The YAB:Cr³⁺ phosphor has an intense broadband absorption to the blue light, simultaneously exhibiting the sharp-line ²E emission and the broadband ⁴ T₂ emission of Cr³⁺ with a QY of ~86.7%. The far-red broadband emissions of YAB:Cr³⁺ centered at ~735 nm show a high resemblance to the active-state (P_FR) absorption of plant phytochrome. Moreover, the YAB:Cr³⁺ phosphor shows the thermally enhanced luminescence at temperatures of 303−393 K and the near-zero thermal quenching up to 423 K. The anomalous thermal enhancement is attributed to the temperature-dependent repopulation between ²E and ⁴ T₂ states. Finally, a pc-LED device was fabricated with the YAB:Cr³⁺ phosphor and blue chip, exhibiting the light out power of ~50.6 mW and energy conversion efficiency of ~17.4% at 100 mA drive current, respectively. The exceptional PL features including suitable excitation/emission wavelengths, suppressed thermal quenching and high QY make YAB:Cr³⁺ phosphors very promising for applications in plant growth pc-LEDs.     

临兴区块新型储层保护钻井液技术研究与应用

临兴区块地层非均质性强,具有低孔、低渗、低温、低压的特点,需要后期压裂改造,才能实现工业化气流.随着该区域的钻井数量逐渐增多,储层伤害问题日益突出,笔者对地层进行了敏感性分析,在此基础上,研制了超双疏剂,并对其性能进行了评价.结果表明:超双疏剂能够使岩心孔喉表面润湿性由亲水亲油向疏水疏油转变,有效降低低渗储层发生自吸水锁概率,达到保护储层的目的;同时,3％质量分数的超双疏剂比传统的抑制剂KCl和聚醚胺等具有更好的抑制性能.现场应用表明,加入超双疏剂后的钻井液黏度低、切力高、老化前后性能稳定,应用双疏钻井液体系后现场平均机械钻速提高32.33％,井眼扩大率降低33.89％,作业井日产量平均在35973.5 m3/d.     

水力空化改质对重质原油沥青质及性质的影响

利用水力空化过程产生局部的高温、高压、高射流以及强大的剪切力等极端化学物理条件改质处理沙特重质原油，试验结果表明：沙特重质原油经过水力空化改质后粘度由13.61降低至7.22mm2/s，残碳由7.16%降低至6.48%，实沸点蒸馏后减压渣油降低1个百分点。进一步采用APPI FT-IR MS、XRD、FT-IR、SEM和粒度分布等技术研究了水力空化改质对沙重原油分子组成，沥青质团聚体微晶结构、沥青质胶束粒径分布、沥青质官能团、沥青质形貌等方面的影响，从分子角度阐述空化改质重油的机理。研究结果表明：水力空化改质后沙重原油分子量分布、芳烃类化合物缔合作用变小；沥青质对低DBE化合物吸附性能降低；沥青质团聚体微晶结构更加松散；沥青质胶束粒度分布降低；沥青质分子相互团聚作用力减弱。进一步考察了水力空化改质前后减压渣油延迟焦化性能，改质处理后焦炭产率降低1.85个百分点，液体收率和气体产率分别增加1.52和0.33个百分点，水力空化改质对沥青质性质、结构特点的改善能够有效的提高其加工性能。